Setting up the Pioneer 12 Plus correctly is the first step toward a safe and enjoyable riding experience. Designed as a 12-inch electric mini bike for kids, the Pioneer 12 Plus arrives partially assembled and requires final setup by an adult.
Before Assembly: Important Safety Notes
Before you begin, please read and follow these key safety reminders:
-
The Pioneer 12 Plus is intended as a toy, not a means of transportation
-
Adult assembly and supervision are required at all times
-
Do not allow children under 7 years old to operate the bike
-
Always check that all components are securely tightened before riding
Choose a clean, flat workspace and ensure all parts are present before assembly.
What’s Included in the Box
-
Partially assembled Pioneer 12 Plus mini bike
-
Front wheel with axle and nuts
-
Handlebar clamps and bolts
-
Pedals (left and right)
-
Charger
-
Assembly tools
If any parts appear damaged or missing, do not proceed with assembly.
Assembly Instructions
Step 1: Install the Front Wheel
Carefully position the front wheel between the front fork.
-
Align the inner bearing sleeve correctly
-
Insert the axle through the wheel and fork
-
Secure all hardware firmly
Once installed, spin the wheel to confirm it rotates freely without obstruction.
Warning: Take care during this step, as the front fork contains sharp edges.
Step 2: Install and Adjust the Handlebar
Place the handlebar into the handlebar clamp in an upright position.
-
Insert all bolts evenly
-
Tighten securely until the handlebar does not move forward or backward
-
Ensure throttle and brake cables are not pinched
To adjust the handlebar position later, loosen the bolts slightly, reposition, and retighten fully.
Step 3: Install the Pedals
Attach each pedal to its designated side and tighten securely using the provided tools. Confirm both pedals are firmly fixed before riding.
Charging the Battery (Before First Ride)
The Pioneer 12 Plus must be fully charged before its first use.
Charging steps:
-
Turn the power off before charging
-
Plug the charger into a wall outlet (indicator light shows green)
-
Connect the charger to the bike’s charging port
-
Charging indicator turns red while charging and green when fully charged
Charging safety guidelines:
-
Use only the supplied 24V charger
-
Charge indoors in a dry, well-ventilated area
-
Do not use the charger if the cable or plug is damaged
-
Avoid charging in extreme temperatures
Getting Ready to Ride
After assembly and charging:
-
Sit on the bike with both hands on the handlebars
-
Turn on the power
-
Gently apply the throttle using the right hand
-
To stop, release the throttle and apply the brake until fully stopped
The display shows battery level and speed mode. The Pioneer 12 Plus features three speed modes up to a maximum of 10 mph.
Routine Maintenance & Care
Regular inspections and basic care help extend the life of the Pioneer 12 Plus.
Hardware & Safety Checks
-
Inspect bolts, nuts, and fasteners frequently
-
Tighten any loose parts immediately
-
Check the frame and handlebars for cracks or damage
Cleaning & Storage
-
Clean using a dry or slightly damp cloth
-
Do not spray with a hose or submerge in water
-
Store indoors during rainy or snowy conditions
Tires
-
Check tire pressure before riding
-
Inspect tires for wear and replace if tread is excessively worn
Battery Care
-
Avoid overcharging once fully charged
-
Recharge the battery at least once every 1–2 months during long-term storage
-
Store the bike in a cool, dry place
Error Code Indicators
If an error code appears on the display or LED indicator, stop riding and inspect the bike.
| Headlight LED | Error |
| E0 | Communication failure (instrument cannot receive data) |
| E1 | Handlebar failure |
| E2 | Brake lever malfunction |
| E3 | Hall sensor error |
| E4 | MOS malfunction |
| E5 | Mainboard malfunction |
| E6 | Battery failure |
Contact support if the issue cannot be resolved.
Need Assistance?
If you experience any issues during assembly, charging, or maintenance, discontinue use and contact official customer support for guidance. Proper servicing helps ensure safety and protects product performance.
FAQs
What’s the maximum load?
144 lb (65 kg).
How long does charging take, and how do I know it’s done?
Charging time is listed as about 4 hours. The charger indicator is red while charging and green when fully charged.
Can I use a different charger?
The manual specifies using the 24V charger intended for the product. Don’t use damaged chargers/cables.
Does it arrive fully assembled?
It arrives partially assembled and requires final assembly by an adult.
